Easy step by step guide on how to gather Toyota OBD1 codes and definition table.
- Toyota Dtc Codes Download For Windows 7
- Toyota Dtc 25
- Toyota Dtc Codes Download For Pc
- 2000 Toyota Dtc Codes
Nov 21, 2017 P/S system fault codes of Toyota Hilux. To check, open the TC and CG terminals of the DLC 3 connector. And read the trouble codes according to the number of P / S indicator flashes. To remove errors, plug out the TS and CG pins of the DLC 3. Connect the ignition and within 8 seconds. Ok Guys - Thanks to Marc M of the Tacoma forum, here is a list of the OBD-II Codes as listed on a Matrix owners site. Has been updated to the Master Sticky (or will be very shortly). So here goes - And please note: The P1xxx codes are all Toyota Specific, and the P0xxx are General and will relate to all cars. Diagnostic Codes - Toyota. B2799 Toyota Description This Diagnostic Trouble Code (DTC) is output when the Engine Control Module detects errors in communication between the Transponder Key Electronic Control Unit (ECU) assembly and the ECM, or in the communication lines.This DTC is also output when an engine start is attempted while the ECU communication ID between the transponder key ECU assembly and the ECM is different. NOTICE about Toyota Specific OBD II Diagnostic Trouble Codes (DTC) PDF download. Sometimes due server overload owners manual could not be loaded. Try to refresh or download newest Adobe Flash plugin for desktop or Flash Player for Android devices. Try to upgrade your browser. Cost of diagnosing the C1201 TOYOTA code. Labor: 1.0 The cost of diagnosing the C1201 TOYOTA code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle's make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour.
Step 1 - To gather trouble codes locate the diagnostic connector under the hood near passengers fender, or under the dash on the driver’s side.
Step 2 - Use a jumper wire connect the TE1 and T1 terminals (For Tercel and MR2 use the T and E1 terminals).
Step 3 - Turn the ignition key to the 'ON' position and observe the check engine light, count the number of times it blinks which will be the first digit of the two digit trouble code, the check engine light will pause shortly followed by the second digit of the trouble code. For example; if the check engine light blinks once and pauses followed by six blinks the trouble code number would be 16.
If no code is present the check engine light will stay on constantly, to restart code gathering turn the ignition key to the 'OFF' position, wait three minutes and turn the ignition key back 'ON' again. Remove the jumper wire once code gathering is complete. To clear code after the repairs have been made remove the negative battery cable for one minute and reconnect.
Code Definition Table
Code 11 Momentary interruption in power supply to ECU (electronic control unit or computer) up to 1991
Code 12 Engine revolution signal missing
Code 13 Rpm signal to ecu missing above 1000 rpm
Code 14 Igniter signal to ecu missing
Code 16 A/T control signal missing from ecu
Toyota Dtc Codes Download For Windows 7
Code 21 Main oxygen sensor signal fault
Code 22 Water temperature sensor circuit fault
Code 23 and 24 Intake air temperature signal fault
Toyota Dtc 25
Code 25 Air/fuel ratio LEAN
Code 26 Air/fuel ratio RICH
Code 27 Sub-oxygen sensor signal or heater circuit fault
Code 28 No. 2 oxygen sensor/heater signal fault
Code 31 and 32 Air flow meter circuit or Vacuum sensor signal fault
Code 34 and 36 Turbo-charging pressure signal fault
Code 35 Altitude compensation sensor signal fault
Code 41 Throttle position circuit fault
Code 42 Vehicle speed sensor circuit
Code 43 No starter signal to the ecu
Code 51 AC signal on; DL contact off (in transmission shifter with diagnostic connector jumped)
Toyota Dtc Codes Download For Pc
Code 52, 53 and 55 Knock sensor fault Code 71 EGR system malfunction
Code 72 Fuel cut solenoid signal fault
Code 78 Fuel pump control signal fault
2000 Toyota Dtc Codes
Code 81, 83, 84 and 85 TCM communication fault